TYBT2-IPEX 模组规格书

更新时间:2025-03-04 10:22:45下载pdf

1.产品概述

TYBT2-IPEX 是由涂鸦智能开发的一款嵌入式的蓝牙模块。它主要由一个高集成度的蓝牙芯片 TLSR8266 和少量的外围电路构成,内置了蓝牙网络通信协议栈和丰富的库函数。TYBT2-IPEX 还包含低功耗的 32 位 MCU,蓝牙 LE/2.4G Radio,512Kbyte flash, 16Kbyte SRAM, 9 个可复用的 IO 口。

特点

  • 内置低功耗 32 位 MCU,可以兼作应用处理器

​ 主频支持 48MHz

  • 工作电压:1.9V-3.6V

  • 外设:1xI2C,5xPWMs,1xUART

  • 蓝牙 RF 特性

    兼容 蓝牙 LE 4.0

    射频数据速率高达 2Mbps

    TX 发射功率:+7dBm

    RX 接收灵敏度:-92dBm

    内嵌硬件 AES 加密

    外接 2.4G 天线

    工作温度:-20℃ to 105℃

主要应用领域

  • 智能 LED
  • 智慧家居
  • 智能低功耗传感器

2.模块接口

尺寸封装

TYBT2-IPEX 有两排引脚,引脚间距为 1.5mm。

TYBT2-IPEX   尺寸大小:15mm (W)×15.2mm (L)封装如图 2.1 所示:

TYBT2-IPEX 模组规格书
图 2.1 TYBT2-IPEX 示意图

引脚定义

接口引脚定义如表 2.2 所示:

​ 表 2.2 TYBT2-IPEX 接口引脚排列说明

序号 符号 IO 类型 功能
1 SDA I/O I2C 的数据线引脚,内部有 4.7K 上拉电阻,可做普通 IO 口。
2 SCL I/O I2C 的时钟线引脚,内部有 4.7K 上拉电阻,可做普通 IO 口。
3 G I/O 普通 IO 口,可作 LED 驱动的 PWM 输出,默认控制绿光。
4 B I/O 普通 IO 口,可作 LED 驱动的 PWM 输出,默认控制蓝光。
5 WW I/O 普通 IO 口,可作 LED 驱动的 PWM 输出,默认控制暖白光。
6 CW I/O 普通 IO 口,可作 LED 驱动的 PWM 输出,默认控制冷白光。
7 R I/O 普通 IO 口,可作 LED 驱动的 PWM 输出,默认控制红光。
8 3.3V P 模块电源输入引脚。
9 TX I/O 串口发送引脚,可作普通 IO 口。
10 RX I/O 串口发送引脚,可作普通 IO 口。
11 GND P 模块电源参考地引脚。
12 SW I/O 蓝牙芯片烧录引脚。
13 RST I 模块复位引脚,内部有 4.7K 上拉电阻。
14 GND P 模块电源参考地引脚。

说明:P 表示电源引脚,I/O 表示输入输出引脚。

​ SW 只做模块的固件的烧录,不可用作它用。

​ SDA、SCL 引脚模块没有接上拉电阻,可做 GPIO 使用,当 I2C 使用时,外部需要加 4.7K 上拉电阻。

​ WW 引脚做 PWM 输出时,极性与 R、G、B、CW 做 PWM 输出时相反。

​ 如对 PWM 输出控制的灯色有自己的需求,请与我司商务联系。

3.电气参数

绝对电气参数

​ 表 3.1 绝对参数

参数 描述 最小值 最大值 单位
Ts 存储温度 -20 85
VCC 供电电压 -0.3 3.9 V
静电释放电压(人体模型) TAMB-25℃ - 2 KV
静电释放电压(机器模型) TAMB-25℃ - 0.5 KV

工作条件

​ 表 3.2 正常工作条件

参数 描述 最小值 典型值 最大值 单位
Ta 工作温度 -20 - 85
VCC 工作电压 2.5 3.3 3.6 V
VIL IO 低电平输入 -0.3 - VCC*0.25 V
VIH IO 高电平输入 VCC*0.75 - VCC V
VOL IO 低电平输出 - - VCC*0.1 V
VOH IO 高电平输出 VCC*0.8 - VCC V

工作模式下功耗

​ 表 3.3 TX 连续发送时功耗

符号 条件 典型值 单位
Itx 连续发送,0dBm 输出功率 13 mA
Irx 连续接收 13 mA
IDC 联网工作状态下 80 uA

4.射频特征

基本射频特征

​ 表 4.1  射频基本特性

参数项 详细说明
工作频率 2.4GHz ISM band
无线标准 蓝牙 LE 4.0
数据传输速率 1Mbps,2Mbps
天线类型 板上预留天线接口,外接 2.4G 天线

RF 输出功率

​ 表 4.2 TX 连续发送时功率

参数项 最小值 典型值 最大值 单位
RF 平均输出功率 3.8 7 - dBm
20dB 占用带宽 - 1000 - KHz

RF 接收灵敏度

​ 表 4.3 RX 灵敏度

参数项 最小值 典型值 最大值 单位
RX 灵敏度 1Mbps -93 -92 -90 dBm
频率偏移误差 - -300 - +300 KHz
同信道干扰抑制 - - -7 - dB

天线信息

天线类型

TYBT2-IPEX 需要外接 2.4GHz 频段的天线,天线一端带 IPEX 一代端子。

降低天线干扰

为确保 RF 性能的最优化,建议模块天线部分和其他金属件距离至少在 15mm 以上。天线最好靠近边缘放置,天线周围不能被金属物包围,不能被一些高器件遮挡,尽量减少射频性能的衰减,以利于射频信号自由辐射出来,

有两个及以上的同频段天线时,空间上尽量拉开天线之间的距离,最好大于 5cm, 保证良好的隔离度。

6.封装信息及生产指导

机械尺寸和背面焊盘尺寸

TYBT2-IPEX 模组规格书

​ 图 6.1 TYBT2-IPEX 尺寸图

生产指南

  1. 涂鸦出厂的贴片封装模组建议使用SMT机器贴片,拆开包装后建议在24小时内完成焊接,如果拆封后未使用完建议放置在湿度不超过10%RH的干燥柜内,或重新进行真空包装并记录暴露时间,总暴露时间不超过168小时。
    • SMT贴片所需仪器或设备:
      • 贴片机
      • SPI
      • 回流焊
      • 炉温测试仪
      • AOI
    • 烘烤所需仪器或设备:
      • 柜式烘烤箱
      • 防静电耐高温托盘
      • 防静电耐高温手套
  2. 涂鸦出厂的模组存储条件如下:
    • 防潮袋必须储存在温度<40℃、湿度<90%RH的环境中

    • 干燥包装的产品,保质期为从包装密封之日起12个月的时间

    • 密封包装内装有湿度指示卡:

      TYBT2-IPEX 模组规格书

  3. 涂鸦出厂的模组当出现可能受潮的情况下需要进行烘烤:
    • 拆封前发现真空包装袋破损
    • 拆封后发现包装袋内没有湿度指示卡
    • 拆封后如果湿度指示卡读取到10%及以上色环变为粉色
    • 拆封后总暴露时间超过168小时
    • 从首次密封包装之日起超过12个月
  4. 烘烤参数如下:
    • 烘烤温度:卷盘包装60℃,湿度小于等于5%RH;托盘包装125℃,湿度小于等于5%RH(耐高温托盘非吸塑盒拖盘)
    • 烘烤时间:卷盘包装48小时;托盘包装12小时
    • 报警温度设定:卷盘包装65℃;托盘包装135℃
    • 自然条件下冷却到36℃以下后,即可进行生产
    • 若烘烤后暴露时间大于168小时没有使用完,请再次进行烘烤
    • 如果暴露时间超过168小时未经过烘烤,不建议使用回流焊接工艺焊接此批次模组,因模组为3级湿敏器件超过允许的暴露时间产品可能受潮,进行高温焊接时可能会导致器件失效或焊接不良
  5. 在整个生产过程中请对模组进行静电放电(ESD)保护。
  6. 为了确保产品合格率,建议使用SPI和AOI测试设备来监控锡膏印刷和贴装品质。

推荐炉温曲线

请根据回流焊曲线图进行SMT贴片,峰值温度245℃,回流焊温度曲线如下图所示:

TYBT2-IPEX 模组规格书

  • A:温度轴

  • B:时间轴

  • C:合金液相线温度:217-220℃

  • D:升温斜率:1-3℃/S

  • E:恒温时间:60-120S;恒温温度:150-200℃

  • F:液相线以上时间:50-70S

  • G:峰值温度:235-245℃

  • H:降温斜率:1-4℃/S

    注意:以上推荐曲线以SAC305合金焊膏为例。其他合金焊膏请按焊膏规格书推荐炉温曲线设置。

储存条件

TYBT2-IPEX 模组规格书

附录:声明

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This device has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the device and receiver.
  • Connect the device to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled rolled environment. This device should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Important Note

This radio module must not be installed to co-locate and operate simultaneously with other radios in the host system except following FCC multi-transmitter product procedures. Additional testing and device authorization may be required to operate simultaneously with other radios.

The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible to the end-user.

The host product manufacturer is responsible for compliance with any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.

The end-user manual shall include all required regulatory information/warnings as shown in this manual, including “This product must be installed and operated with a minimum distance of 20 cm between the radiator and user body”.

The RF module is considered as a limited modular transmitter according to FCC rules. Even though the RF module gets an FCC ID, the host product manufacturer can not use the FCC ID on the final product directly. In these circumstances, the host product manufacturer integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining the FCC authorization by a Class II permissive change application or a new application.

Declaration of Conformity European Notice

TYBT2-IPEX 模组规格书

Hereby, Hangzhou Tuya Information Technology Co., Ltd declares that this module product is in compliance with essential requirements and other relevant provisions of Directive 2014/53/EU,2011/65/EU. A copy of the Declaration of conformity can be found at https://www.tuya.com.

TYBT2-IPEX 模组规格书

This product must not be disposed of as normal household waste, in accordance with the EU directive for waste electrical and electronic equipment (WEEE-2012/19/EU). Instead, it should be disposed of by returning it to the point of sale, or to a municipal recycling collection point.

The device could be used with a separation distance of 20cm from the human body.