TYBN1 模组规格书

更新时间:2022-08-04 02:23:37下载pdf

产品概述

TYBN1 是由涂鸦智能开发的一款低功耗嵌入式的蓝牙模块。它主要由一个高集成度的蓝牙芯片 nRF52832 和少量的外围电路构成,内置了蓝牙网络通信协议栈和丰富的库函数。TYBN1 包含一个 Cortex-M4 内核的低功耗32 位 MCU,集成 BLE/2.4G Radio、512Kbyte flash、64Kbyte SRAM 和 11 个可复用的 IO 口,最高可支持 4 路 ADC 输入。

特点

  • 内置低功耗 32 位 MCU,可以兼作应用处理器。
  • 主频支持 64 MHz
  • 工作电压:1.7V-3.6V
  • 外设:1xI2C、3xPWMs、1xUART
  • BLE RF 特性
    • 兼容 BLE5.0
    • 射频数据速率高达 2Mbps
    • TX 发射功率:+10dBm
    • RX 接收灵敏度:-94.5dBm@BLE 1Mbps
    • 内嵌硬件 AES 加密
    • 搭配板载 PCB 天线
    • 工作温度:-20℃ 到 +85℃

主要应用领域

  • 智能 LED
  • 智能家居
  • 智能低功耗传感器

模块接口

尺寸封装

  • TYBN1 有两排共计 18 个引脚,引脚间距为 1.5mm。

  • TYBN1 尺寸大小:16 ±0.35mm(W)×21±0.35mm (L)x2.0±0.15mm(H),其中 PCB 板厚 1.0±0.1mm。

    封装如下图所示:

    TYBN1 模组规格书

    TYBN1 模组规格书

引脚定义

接口引脚定义如下表所示:

序号 符号 IO 类型 功能
1 GND P 模块参考地引脚
2 IO19 I/O 普通 GPIO 口,对应 IC Pin22。
3 IO12 I/O 普通 GPIO 口,对应 IC Pin15,
4 IO4_A I/O GPIO 口,可配置成 ADC 口,对应 IC Pin6。
5 IO5_A I/O GPIO 口,可配置成 ADC 口,对应 IC Pin7。
6 IO3_A I/O GPIO 口,可配置成 AD C口,对应 IC Pin5。
7 IO2_A I/O GPIO 口,可配置成 ADC 口,对应 IC Pin4。
8 GND P 模块参考地引脚
9 3.3V P 模块电源输入引脚
10 IO11 I/O 普通 GPIO 口,对应 IC Pin14。
11 IO14_D I/O 普通 GPIO 口,对应 IC Pin17。
12 IO15_D I/O 普通 GPIO 口,对应 IC Pin18。
13 IO16_D I/O 普通 GPIO 口,对应 IC Pin19。
14 IO18_D I/O 串口 TXD 管脚,对应 IC Pin21。
15 IO20_D I/O 串口 RXD 管脚,对应 IC Pin23。
16 IO21 I 模组复位管脚,内部已经有上拉电阻,低电平有效,对应 IC Pin24。
17 SWC I JLINK 通信时钟引脚,对应 IC Pin25。
18 SWDIO I/O JLINK 通信数据引脚,对应 IC Pin26。

说明P 表示电源引脚,I/O 表示输入输出引脚,AI表示模拟输入。

如对 PWM 输出控制的灯色有自己的需求,请与我司商务联系。

电气参数

绝对电气参数

参数 描述 最小值 最大值 单位
Ts 存储温度 -40 125
VCC 供电电压 -0.3 3.9 V
静电释放电压(人体模型) TAMB-25℃ - 2 KV
静电释放电压(机器模型) TAMB-25℃ - 1 KV

工作条件

参数 描述 最小值 典型值 最大值 单位
Ta 工作温度 -20 - 85
VCC 工作电压 1.7 3.3 3.6 V
VIL IO 低电平输入 -0.3 - VCC*0.3 V
VIH IO 高电平输入 VCC-0.3 - VCC +0.3 V
VOL IO 低电平输出 VSS - 0.3 V
VoH IO 高电平输出 VCC-0.3 - VCC V

工作模式下功耗

符号 条件 典型值 单位
Itx 连续发送,0dBm 输出功率 7.5 mA
Irx 连续接收 6 mA
IDC Mesh 联网工作状态下 13 mA
Ideepsleep 休眠模式 1 μA

射频特性

基本射频特性

参数项 详细说明
工作频率 2.4GHz ISM band
无线标准 BLE 5.0
数据传输速率 1Mbps,2Mbps
天线类型 板载 PCB 天线

RF 输出功率

参数项 最小值 典型值 最大值 单位
RF 平均输出功率 -40 4 4 dBm
20dB 占用带宽(1M) - 1300 - KHz
20dB 占用带宽(2M) - 2600 - KHz

RF 接收灵敏度

参数项 典型值 典型值 最大值 单位
RX 灵敏度 1Mbps -93 -93 -90 dBm
RX 灵敏度 2Mbps -92 -96 -89 dBm
频率偏移误差 1Mbps -250 - +250 KHz
频率偏移误差 2Mbps -320 - +320 KHz
同信道干扰抑制 - - -7 - dB

天线信息

天线类型

TYBN1 使用的 PCB 天线是 2.400GHz-2.483GHz 频段的 PCB 板载天线。

降低天线干扰

为确保 RF 性能的最优化,建议模块天线部分和其他金属件距离至少在 15mm 以上。

由于 TYBN1 是通过 SMT 工艺,贴到主控板上配合其他元器件一起应用。那么 PCB 天线的摆放位置和摆放方式会直接影响 RF 性能。以下是我们推荐的摆放位置,和不建议的摆放位置。

  • TYBN1 天线的各个摆放位置如图所示,推荐使用方案 1 和方案 2 的摆放位置,天线在板框外或天线附近挖空。性能和单独模块 RF 测试性能基本一致。

  • 如果设计受限必须将 PCB 天线放在底板上,可以参考方案 3 的摆放方式,天线在板框内,但天线附近不覆铜和走线。但射频性能会有一些损失,差不多衰减 1-2dBm。

  • 不建议使用方案 4 的摆放位置,天线在板框内,且天线下覆铜或走线。射频信号会明显的衰减。

    TYBN1 模组规格书

    TYBN1 模组规格书

封装信息及生产指导

机械尺寸和背面焊盘尺寸

TYBN1 模组规格书

说明:默认的模组外形尺寸公差为 ±0.35 mm,关键尺寸公差 ±0.1 mm。关键尺寸如果客户有明确要求,请沟通后在规格书中进行明确的标定。

生产指南

  1. 涂鸦出厂的贴片封装模组建议使用 SMT 机器贴片,拆开包装后建议在 24 小时内完成焊接。如果拆封后未使用完,建议放置在湿度不超过 10%RH 的干燥柜内,或重新进行真空包装并记录暴露时间。总暴露时间不超过 168 小时。

    • SMT 贴片所需仪器或设备:
      • 贴片机
      • SPI
      • 回流焊
      • 炉温测试仪
      • AOI
    • 烘烤所需仪器或设备:
      • 柜式烘烤箱
      • 防静电耐高温托盘
      • 防静电耐高温手套
  2. 涂鸦出厂的模组存储条件如下:

    • 防潮袋必须储存在温度 <40℃、湿度 <90%RH 的环境中。

    • 干燥包装的产品,保质期为从包装密封之日起 12 个月的时间。

    • 密封包装内装有湿度指示卡:

      TYBN1 模组规格书

  3. 涂鸦出厂的模组当出现可能受潮的情况下需要进行烘烤:

    • 拆封前发现真空包装袋破损。
    • 拆封后发现包装袋内没有湿度指示卡。
    • 拆封后如果湿度指示卡读取到 10% 及以上色环变为粉色。
    • 拆封后总暴露时间超过 168 小时。
    • 从首次密封包装之日起超过 12 个月。
  4. 烘烤参数如下:

    • 烘烤温度:卷盘包装 40℃,小于等于 5%RH。托盘包装 125℃,小于等于 5%RH(耐高温托盘非吸塑盒拖盘)。
    • 烘烤时间:卷盘包装 168 小时,托盘包装 12 小时。
    • 报警温度设定:卷盘包装 50℃,托盘包装 135℃。
    • 自然条件下冷却到 36℃ 以下后,即可进行生产。
    • 若烘烤后暴露时间大于 168 小时没有使用完,请再次进行烘烤。
    • 如果暴露时间超过 168 小时未经过烘烤,不建议使用波峰焊接工艺焊接此批次模组,因模组为 3 级湿敏器件超过允许的暴露时间很可能受潮,进行高温焊接时可能导致器件失效或焊接不良。
  5. 在整个生产过程中请对模组进行静电放电(ESD)保护。

  6. 为了确保产品合格率,建议使用 SPI 和 AOI 测试设备来监控锡膏印刷和贴装品质。

推荐炉温曲线

请根据回流焊曲线图进行 SMT 贴片,峰值温度 245℃,回流焊温度曲线如下图所示:

TYBN1 模组规格书

  • A:温度轴

  • B:时间轴

  • C:合金液相线温度:217-220℃

  • D:升温斜率:1-3℃/S

  • E:恒温时间:60-120S,恒温温度:150-200℃

  • F:液相线以上时间:50-70S

  • G:峰值温度:235-245℃

  • H:降温斜率:1-4℃/S

    注意:以上推荐曲线以 SAC305 合金焊膏为例。其他合金焊膏请按焊膏规格书推荐炉温曲线设置。

储存条件

TYBN1 模组规格书

模块 MOQ 与包装信息

产品型号 MOQ(pcs) 出货包装方式 出货包装方式 每箱包装卷盘数(盘)
TYBN1 3600 载带卷盘 900 4

附录:声明

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which
    the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled rolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.

Important Note

This radio module must not be installed to co-locate and operating simultaneously with other radios in the host system except in accordance with FCC multi-transmitter product procedures. Additional testing and equipment authorization may be required to operate simultaneously with other radio.

The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end-user.

The host product manufacturer is responsible for compliance with any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.

The end-user manual shall include all required regulatory information/warnings as shown in this manual, including this product must be installed and operated with a minimum distance of 20 cm between the radiator and user body.

The RF module is considered as a limited modular transmitter according to FCC rules. Even though the RF module gets an FCC ID, the host product manufacturer can not use the FCC ID on the final product directly. In these circumstances, the host product manufacturer integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining the FCC authorization by a Class II permissive change application or a new application.

Declaration of Conformity European notice

TYBN1 模组规格书

Hereby, Hangzhou Tuya Information Technology Co., Ltd declares that this module product is in compliance with essential requirements and other relevant provisions of Directive 2014/53/EU,2011/65/EU.A copy of the Declaration of conformity can be found at https://www.tuya.com

TYBN1 模组规格书

This product must not be disposed of as normal household waste, in accordance with the EU directive for waste electrical and electronic equipment (WEEE- 2012/19/EU). Instead,it should be disposed of by returning it to the point of sale, or to a municipal recycling collection point.

The device could be used with a separation distance of 20cm to the human body.