JWBR2S-3.3V 模组规格书

产品概述

JWBR2S-3.3V是由杭州涂鸦科技有限公司开发的一款适用于3.3V TTL电平的串口通信的Wi-Fi模组。它主要由我司自主开发的双模WiFi +蓝牙WBR1模组和电平转换电路构成，内置了Wi-Fi/BT网络协议栈和我司的串口对接协议。
JWBR2S-3.3V是一个RTOS平台，用户可以基于串口通信对接方式，开发满足自己需求的嵌入式产品。

特性

• 内置低功耗KM4-MCU，可以兼作应用处理器
  • 最大主频支持100MHz
• 工作电压：3.3V
• 外设：1×UART
• Wi-Fi 连通性
  • 802.11 b/g/n20
  • 通道1-14@2.4GHz
  • 持Bluetooth 4.2 Low Energy
  • 支持WPA/WPA2 安全模式
  • 802.11b模式下最大+18dBm的输出功率
  • 支持SmartConfig （包括Android和IOS设备）
  • 板载PCB On Board 天线
  • 工作温度：-20℃ to 85℃

应用领域

• 智能楼宇
• 智慧家居/家电
• 智能插座
• 智能照明
• 工业无线控制
• 婴儿监控器
• 网络摄像头
• 智能公交

更新说明

更新日期	更新内容	更新后版本
2020-02-26	新建文档	V2.0.0

模组接口

尺寸封装

JWBR2S-3.3V电气接口为PH-4AW连接器，引脚间距为2.0mm。
JWBR2S-3.3V 尺寸大小：42.6mm±0.35mm(W)×31±0.35mm(L) ×9.1±0.15mm (H),其中PCB厚度1.2mm±0.1 mm,模组尺寸如下图所示：

引脚定义

引脚序号	符号	IO类型	功能
1	RX	I/O	UART0_RXD，模组通信RX口，输入3.3V TTL电平
2	TX	I/O	UART0_TXD，模组通信TX口，输出3.3V TTL电平
3	GND	P	电源参考地
4	VCC	P	模组的电源引脚（3.3V）
说明：P表示电源引脚，I/O表示输入输出引脚

测试点定义

引脚序号	符号	IO类型	功能
1	3.3V	P	模组内部电源引脚（3.3V）
2	GND	P	电源参考地
3	Log_Tx	I/O	UART_Log_TXD(用于打印模组内部信息)
4	Log_Rx	I/O	UART_Log_RXD (用于打印模组内部信息)
5	RXD	I/O	模组固件烧录口，
6	TXD	I/O	模组固件烧录口，
7	A_0	I/O	GPIOA_0，模组固件烧录口，烧录时该引脚需要拉高至3.3V。
8	RST	I/O	模组硬件复位引脚

说明：P表示电源引脚，I/O表示输入输出引脚，测试点禁止使用。

电气参数

绝对电气参数

参数	描述	最小值	最大值	单位
Ts	存储温度	-40	105	℃
VBAT	供电电压	-0.3	3.3	V
静电释放电压（人体模型）	TAMB-25℃	-	2	KV
静电释放电压（机器模型）	TAMB-25℃	-	0.5	KV

正常工作条件

参数	描述	最小值	典型值	最大值	单位
Ta	工作温度	-20	-	85	℃
VBAT	供电电压	3.0	3.3	3.6	V
VIL	IO低电平输入	-0.3	-	VCC*0.25	V
VIH	IO高电平输入	VCC*0.75	-	VCC	V
VOL	IO低电平输出	-	-	VCC*0.1	V
VoH	IO高电平输出	VCC*0.8	-	VCC	V
Imax	IO驱动电流	-	-	16	mA
Cpad	输入引脚电容	-	2	-	pF

连续发射功耗

工作状态	模式	速率	发射功率	平均值	峰值(典型值)	单位
发射	11b	11Mbps	+17dBm	217	268	mA
发射	11b	11Mbps	+18dBm	225	280	mA
发射	11g	54Mbps	+15dBm	159	188	mA
发射	11g	54Mbps	+17.5dBm	177	213	mA
发射	11n BW20	MCS7	+13dBm	145	167	mA
发射	11n BW20	MCS7	+16.5dBm	165	193	mA

连续接收功耗

工作状态	模式	接收	平均值	峰值(典型值)	单位
接收	CPU Sleep	11Mbps	63	75	mA
接收	CPU Active	54Mbps	65	78	mA
接收	CPU Active	MCS7	65	78	mA

工作模式下功耗

工作模式	工作状态，Ta=25℃	平均值	峰值(典型值)	单位
快连配网状态	模组处于快连配网状态	74	324	mA
网络连接空闲状态	模组处在联网空闲状态	62	320	mA
网络连接操作状态	模组处于联网工作状态	65	315	mA
断网状态	模组处于断网工作状态	66	322	mA

说明：峰值持续时间约5us,以上参数依据不同的固件功能，参数有所不同。

射频参数

基本射频特性

参数项	详细说明
工作频率	2.400~2.484GHz
Wi-Fi标准	IEEE 802.11b/g/n(通道1-14)
数据传输速率	11b:1,2,5.5, 11 (Mbps)； 11g:6,9,12,18,24,36,48,54(Mbps); 11n: HT20 MCS0~7;
天线类型	PCB天线

发射性能

TX连续发送性能

参数项	最小值	典型值	最大值	单位
RF平均输出功率，802.11b CCK Mode 11M	-	17.5	-	dBm
RF平均输出功率，802.11g OFDM Mode 54M	-	14.5	-	dBm
RF平均输出功率，802.11n OFDM Mode MCS7	-	13.5	-	dBm
频率误差	-20	-	20	ppm

接收性能

RX灵敏度

参数项	最小值	典型值	最大值	单位
PER<8%，RX灵敏度，802.11b DSSS Mode 1M	-	-91	-	dBm
PER<10%，RX灵敏度，802.11g OFDM Mode 54M	-	-75	-	dBm
PER<10%，RX灵敏度，802.11n OFDM Mode MCS7	-	-72	-	dBm

天线信息

天线类型

有PCB板载天线和外接天线两种天线接入方式。默认方式是PCB板载天线。

降低天线干扰

在Wi-Fi模组上使用PCB板载天线时，为确保Wi-Fi性能的最优化，建议模组天线部分和其他金属件距离至少在15mm以上。
用户PCB板在天线区域勿走线甚至覆铜，以免影响天线性能。

天线连接器规格

本模组暂无天线连接器。

封装信息及生产指导

机械尺寸

JWBR2S-3.3V 尺寸大小：42.6mm±0.35mm(W)×31±0.35mm(L) ×9.1±0.15mm (H),其中PCB厚度1.2mm±0.1 mm,模组尺寸如下图所示：

端子规格书

端子为2.0mm*4Pin规格，详细参数如下：

生产指南

出厂的模组存储条件如下：

1. 防潮袋必须存储在温度<30℃，湿度<85%RH的环境中。
2. 干燥包装的产品，其保质期应该是从包装密封之日起6个月的时间。
   注意事项
3. 在生产全过程中，各工位操作人员必须戴静电环。
4. 操作时，严防模组沾水或污物。

推荐炉温曲线

请根据回流焊曲线图进行SMT贴片，峰值温度245℃，回流焊温度曲线如下图所示：

储存条件

附录：声明

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This device has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled rolled environment. This device should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Important Note

This radio module must not be installed to co-locate and operating simultaneously with other radios in the host system except following FCC multi-transmitter product procedures. Additional testing and device authorization may be required to operate simultaneously with other radios.

The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end-user.

The host product manufacturer is responsible for compliance with any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.

The end-user manual shall include all required regulatory information/warnings as shown in this manual, including “This product must be installed and operated with a minimum distance of 20 cm between the radiator and user body”.

This device has got an FCC ID: 2ANDL-JWBR2S-3.3V. The end product must be labeled in a visible area with the following: “Contains Transmitter Module FCC ID: 2ANDL-JWBR2S-3.3V”.

This device is intended only for OEM integrators under the following conditions:

The antenna must be installed such that 20cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna.

As long as the 2 conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.

Declaration of Conformity European Notice

Hereby, Hangzhou Tuya Information Technology Co., Ltd declares that this module product is in compliance with essential requirements and other relevant provisions of Directive 2014/53/EU,2011/65/EU. A copy of the Declaration of conformity can be found at https://www.tuya.com.

This product must not be disposed of as normal household waste, in accordance with the EU directive for waste electrical and electronic equipment (WEEE-2012/19/EU). Instead, it should be disposed of by returning it to the point of sale, or to a municipal recycling collection point.

The device could be used with a separation distance of 20cm to the human body.