WR1E Module Datasheet

WR1E is a low-power embedded Wi-Fi module that Tuya has developed. It consists of a highly integrated wireless RF chip (RTL8710BN) and an external flash chip, with an embedded Wi-Fi network protocol stack and varied library functions.

Overview

With the maximum CPU clock rate of 125 MHz, WR1E contains a low-power ARM CM4F, a WLAN MAC, a 1T1R WLAN module, 256 KB static random-access memory (SRAM), 2 MB flash memory, and extensive peripherals.
WR1E is an RTOS platform that integrates all function libraries of the Wi-Fi MAC and TCP/IP protocols. You can develop embedded Wi-Fi products as required.

Features

• Embedded low-power 32-bit CPU, which can also function as an application processor
• Clock rate: 125MHz
• Operating voltage: 3.0 to 3.6 V
• Peripherals: 6 GPIOs, 2 UARTs, and 1 ADC
• Wi-Fi connectivity
  • 802.11 B/G/N20/N40
  • Channels 1 to 14@2.4 GHz (CH1 to 11 for US/CA and CH1 to 13 for EU/CN)
  • Support WEP/WPA/WPA2/WPA2 PSK（AES） security modes
  • +20 dBm output power in 802.11b mode
  • Support SmartConfig functions for Android and iOS devices
  • Onboard PCB antenna or internal antenna IPEX connector
  • Passed CE and FCC certification
  • Operating temperature: -20 to 85℃

Applications

• Intelligent building
• Smart household and home appliances
• Smart socket and light
• Industrial wireless control
• Baby monitor
• Network camera
• Intelligent bus

Module interfaces

Dimensions and footprint

WR1E has two lines of pins with a 1.5-mm pin spacing. Each line has 9 pins.

The WR1E dimensions are 18±0.35 mm (W)×23.5±0.35 mm (L) ×3.4±0.15 mm (H). The dimensions of WR1E are as follows:

Pin Definition

Definitions on interface pins are shown below:

Pin number	Symbol	Type	Function
1	VCC	P	UART0_TXD power supply conversion (5V or 3.3V)
2	UART0_TXD	I/O	UART0_TXD (user-side serial interface)
3	UART0_RXD	I/O	UART0_RXD (user-side serial interface)
4	VD33	P	Power supply pin (3.3V)
5	GND	P	Power supply reference ground
6	GPIOA_14	I/O	GPIOA_14, hardware PWM, IC Pin 13
7	GPIOA_15	I/O	GPIOA_15, hardware PWM, IC Pin 14
8	LOG_TXD	I/O	UART_Log_TXD (used to display the internal information of the module)
9	GPIOA_12	I/O	GPIOA_12, hardware PWM, IC Pin 17
10	GPIOA_5	I/O	GPIOA_5, hardware PWM, IC Pin 28
11	LOG_RXD	I/O	UART_Log_RXD (used to display the internal information of the module) The module has been pulled up and cannot be used for triggering the high level
12	GPIOA_19	I/O	GPIOA_19, a universal IO port, IC Pin 30
13	GPIOA_22	I/O	GPIOA_22, hardware PWM, IC Pin 31
14	GND	P	Power supply reference ground
15	GND	P	Power supply reference ground
16	CHIP_EN	I/O	When software disables the function, connection by a user fails
17	ADC	AI	ADC port, the maximum input voltage is 5V
18	GND	P	Power supply reference ground

Note: P indicates power supply pins, I/O indicates input/output pins, and AI indicates analog input pins.

Electrical parameters

Absolute electrical parameters

Parameter	Description	Minimum Value	Maximum Value	Unit
Ts	Storage temperature	-40	105	℃
VCC	Power supply voltage	-0.3	3.6	V
ESD voltage (human body model)	TAMB-25℃	-	2	KV
ESD voltage (machine model)	TAMB-25℃	-	0.5	KV

Working conditions

Parameter	Description	Minimum value	Typical value	Maximum value	Unit
Ta	Operating temperature	-20	-	85	℃
VDD	Operating voltage	3.0	-	3.6	V
VIL	IO low-level input	-0.3	-	VDD*0.25	V
VIH	IO high-level input	VDD*0.75	-	3.6	V
VOL	IO low-level output	-	-	VDD*0.1	V
VOH	IO high-level output	VDD*0.8	-	VDD	V
Imax	IO drive current	-	-	16	mA
Cpad	Input pin capacitance	-	2	-	pF

RF power consumption

TX power consumption:

Working status	Mode	Rate	Transmit power/Receive	Average value	Peak value (typical value)	Unit
Transmit	11 b	11 Mbps	+17 dBm	287	367	mA
Transmit	11 b	11 Mbps	+18 dBm	295	382	mA
Transmit	11 g	54 Mbps	+15 dBm	255	406	mA
Transmit	11 g	54 Mbps	+17.5 dBm	267	428	mA
Transmit	11n-HT20	MCS 7	13 dBm	244	395	mA
Transmit	11n-HT20	MCS 7	16.5 dBm	257	422	mA
Transmit	11n-HT40	MCS 7	13 dBm	220	393	mA
Transmit	11n-HT40	MCS 7	16.5 dBm	230	420	mA

Operating current

Working mode	Working status, Ta = 25°C	Average value	Peak value (Typical value)	Unit
Quick connection network state	The module is in the fast network connection state and the Wi-Fi indicator always flashes	115	376	mA
Hotspot network configuration state	The module is in the hotspot network configuration state and the Wi-Fi indicator always flashes slowly	60	386	mA
Network connection operation state	The module is connected to the network and the Wi-Fi indicator is always on	105	389	mA
Disconnected state	The module is disconnected and the Wi-Fi indicator is dark	45	381	mA

RF parameters

Basic RF features

Parameter	Description
Frequency range	2.400 to 2.4835 GHz
Wi-Fi standard	IEEE 802.11b/g/n (channels 1 to 14)
Data transmission rate	11b: 1, 2, 5.5, 11 (Mbps)
Data transmission rate	11g: 6, 9, 12, 18, 24, 36, 48, 54 (Mbps)
Data transmission rate	11n: HT20 MCS 0 to 7
Data transmission rate	11n: HT40 MCS 0 to 7
Antenna type	PCB antenna (default); Antenna to which a U.FL RF connector is externally connected (optional)

TX performance

TX performance

Parameter	Minimum value	Typical value	Maximum value	Unit
Average RF output power, 802.11b CCK Mode 1 M	-	17.5	-	dBm
Average RF output power, 802.11g OFDM Mode 54 M	-	14.5	-	dBm
Average RF output power, 802.11n OFDM Mode MCS 7	-	13.5	-	dBm
Frequency error	-20	-	20	ppm
EVM@802.11b CCK 11 Mbps Mode 17.5 dBm	-	-10	dB
EVM@802.11g OFDM 54 Mbps Mode 15.0 dBm	-	-29	dB
EVM@802.11n OFDM MCS7 Mode 14.0 dBm	-	-30	dB

RX performance

RX sensitivity

Parameter	Minimum value	Typical value	Maximum value	Unit
PER<8%, RX sensitivity, 802.11b CCK Mode 1 M	-	-91	-	dBm
PER<10%, RX sensitivity, 802.11g OFDM Mode 54M	-	-75	-	dBm
PER<10%, RX sensitivity, 802.11n OFDM Mode MCS7	-	-72	-	dBm

Antenna information

Antenna type

WR1E uses two types of antennas: onboard PCB antenna and external antenna. By default, the onboard PCB antenna is preferred. You can select either of them by configuring a resistor.

Antenna interference reduction

To ensure optimal Wi-Fi performance when the Wi-Fi module uses an onboard PCB antenna, it is recommended that the antenna be at least 15 mm away from other metal parts.

Antenna connector specifications

Parameters of the U.FL RF connector are shown below:

Packaging information and production instructions

Mechanical dimensions

The mechanical dimensions of PCB of WR1E are 18±0.35 mm (W)×23.5±0.35 mm (L) ×0.8±0.1 mm (H).

Diagram of mechanical dimensions of WR1E

Side view

Recommended PCB footprint

Production instructions

1. The Tuya SMT module should be mounted by the SMT device. After being unpacked, it should be soldered within 24 hours. Otherwise, it should be put into the drying cupboard where the RH is not greater than 10%; or it needs to be packaged under vacuum again and the exposure time needs to be recorded (the total exposure time cannot exceed 168 hours).

   • SMT devices:
     • Mounter
     • SPI
     • Reflow soldering machine
     • Thermal profiler
     • Automated optical inspection (AOI) equipment
   • Baking devices:
     • Cabinet oven
     • Anti-electrostatic and heat-resistant trays
     • Anti-electrostatic and heat-resistant gloves

2. Storage conditions for a delivered module:

   • The moisture-proof bag must be placed in an environment where the temperature is below 40°C and the relative humidity is lower than 90%.

   • The shelf life of a dry-packaged product is 12 months from the date when the product is packaged and sealed.

   • There is a humidity indicator card (HIC) in the packaging bag.

     

3. The module needs to be baked in the following cases:

   • The packaging bag is damaged before unpacking.
   • There is no HIC in the packaging bag.
   • After unpacking, circles of 10% and above on the HIC become pink.
   • The total exposure time has lasted for over 168 hours since unpacking.
   • More than 12 months have passed since the sealing of the bag.

4. Baking settings:

   • Temperature: 40°C and ≤ 5% RH for reel package and 125°C and ≤5% RH for tray package (please use the heat-resistant tray rather than plastic container)
   • Time: 168 hours for reel package and 12 hours for tray package
   • Alarm temperature: 50°C for reel package and 135°C for tray package
   • Production-ready temperature after natural cooling: < 36°C
   • Re-baking situation: If a module remains unused for over 168 hours after being baked, it needs to be baked again.
   • If a batch of modules is not baked within 168 hours, do not use wave soldering to solder them. Because these modules are Level-3 moisture-sensitive devices, they are very likely to get damp when exposed beyond the allowable time. In this case, if they are soldered at high temperatures, it may result in device failure or poor soldering.

5. In the whole production process, take electrostatic discharge (ESD) protective measures.

6. To guarantee the passing rate, it is recommended that you use the SPI and AOI to monitor the quality of solder paste printing and mounting.

Recommended oven temperature curve

Set oven temperatures according to the following temperature curve of reflow soldering. The peak temperature is 245°C.

• A: Temperature axis

• B: Time axis

• C: Liquidus temperature: 217 to 220°C

• D: Ramp-up slope: 1 to 3°C/s

• E: Duration of constant temperature: 60 to 120s; the range of constant temperature: 150 to 200°C

• F: Duration above the liquidus: 50 to 70s

• G: Peak temperature: 235 to 245°C

• H: Ramp-down slope: 1 to 4°C/s

  Note: The above curve is just an example of the solder paste SAC305. For more details about other solder pastes, please refer to Recommended oven temperature curve in the solder paste specifications.

Storage conditions

MOQ and packaging information

Product model	MOQ (pcs)	Shipping packaging method	Modules per reel (pcs)	Reels per carton (reel)
WR1E	3600	Tape reel	900	4

Appendix: Statement

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This device has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the device and receiver.
• Connect the device to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled rolled environment. This device should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Important Note

This radio module must not be installed to co-locate and operate simultaneously with other radios in the host system except following FCC multi-transmitter product procedures. Additional testing and device authorization may be required to operate simultaneously with other radios.

The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible to the end-user.

The host product manufacturer is responsible for compliance with any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.

The end-user manual shall include all required regulatory information/warnings as shown in this manual, including “This product must be installed and operated with a minimum distance of 20 cm between the radiator and user body”.

This device has got an FCC ID: 2ANDL-WR1E. The end product must be labeled in a visible area with the following: “Contains Transmitter Module FCC ID: 2ANDL-WR1E”.

This device is intended only for OEM integrators under the following conditions:

The antenna must be installed such that 20cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmitter or antenna.

As long as the 2 conditions above are met, further transmitter tests will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.

Declaration of Conformity European Notice

Hereby, Hangzhou Tuya Information Technology Co., Ltd declares that this module product is in compliance with essential requirements and other relevant provisions of Directive 2014/53/EU,2011/65/EU. A copy of the Declaration of Conformity can be found at https://www.tuya.com.

This product must not be disposed of as normal household waste, in accordance with the EU directive for waste electrical and electronic equipment (WEEE-2012/19/EU). Instead, it should be disposed of by returning it to the point of sale, or to a municipal recycling collection point.

The device could be used with a separation distance of 20cm from the human body.