CBLC5 Module Datasheet

Last Updated on : 2024-06-14 03:16:00download

CBLC5 is a low-power embedded Wi-Fi module that Tuya has developed. It consists of a highly integrated RF chip (BK7231N), a few peripherals, an embedded Wi-Fi network protocol stack, and rich library functions.

Overview

CBLC5 not only supports the AP and STA dual-network-connection manner but supports the Bluetooth LE network connection manner.

CBLC5 has a 32-bit MCU with a running speed of up to 120 MHz, 2Mbyte flash, and 256-KB RAM, so as to support the multi-cloud connection. The three 32-bit PWM output makes the chip very suitable for high-quality LED control.

Features

  • Embedded low-power 32-bit CPU, which can also function as an application processor
  • The clock rate: 120 MHz
  • Operating voltage: 3.0V to 3.6V
  • Peripheral: 3 pulse width modulation(PWM)
  • Wi-Fi connectivity
    • 802.11 b/g/n
    • Channels 1 to 14@2.4 GHz
    • Support WEP, WPA/WPA2, WPA/WPA2 PSK (AES), WPA3 security modes
    • Up to + 16 dBm output power in 802.11b mode
    • Support STA/AP/STA+AP working mode
    • Support SmartConfig and AP network configuration manners for Android and iOS devices
    • Operating temperature: -40℃ to 105℃
  • Bluetooth LE connectivity
    • Support the Bluetooth LE V5.2
    • 6 dBm transmit power in Bluetooth mode
    • Complete Bluetooth coexistence interface

Applications

  • Intelligent building
  • Smart household and home appliances
  • Smart socket and light
  • Industrial wireless control

Module interfaces

Dimensions and package

The CBLC5 dimensions are 8.5±0.35 mm (W)×12.7±0.35 mm (L) ×2.6±0.15mm (H).

CBLC5 Module Datasheet

Pin definition

Symbol I/O type Function
ANT O Pad pin for the external antenna
GND P Ground pin
M4 I/O Support hardware PWM and correspond to PA 24 on the internal IC
M5 I/O Support hardware PWM and correspond to PA 26 on the internal IC
M0 I/O Support hardware PWM and correspond to PA 6 on the internal IC
3V3 P Power supply pin

Note: P indicates a power supply pin and I/O indicates an input/output pin.

Definitions of test points

Symbol I/O type Function
R2 I/O UART2_RX, LOG RX, which corresponds to P1 on the internal IC
T2 I/O UART2_TX, LOG TX, which corresponds to P0 on the internal IC
R1 I/O UART1_RX, user serial interface RX, which corresponds to P10 on the internal IC
T1 I/O UART1_TX, user serial interface TX, which corresponds to P11 on the internal IC
CSN I If connected to the ground before powered on, enter the RF test mode. If not connected or connected to VCC before powered on, enter the firmware application mode.
None I RST pin, which corresponds to CEN on the internal IC

Note: Test pins are not recommended.

Electrical parameters

Absolute electrical parameters

Parameter Description Minimum value Maximum value Unit
Ts Storage temperature -55 125
VBAT Power supply voltage -0.3 3.9 V
ESD voltage (human body model) TAMB-25℃ -4 4 KV
ESD voltage (machine model) TAMB-25℃ -200 200 V

Normal working conditions

Parameter Description Minimum value Typical value Maximum value Unit
Ta Operating temperature -40 - 105
VBAT Power supply voltage 3 3.3 3.6 V
VOL I/O low level output VSS - VSS+0.3 V
VOH I/O high level output VBAT-0. 3 - VBAT V
Imax I/O drive current - 6 20 mA
θ Power supply slope 100 - - mV/ms

RF power consumption

Working status Mode Rate Transmit power/receive Average value Peak value (Typical value) Unit
Transmit 11b 11Mbps +16dBm 273 304 mA
Transmit 11g 54Mbps +15dBm 265 280 mA
Transmit 11n MCS7 +14dBm 250 273 mA
Receive 11b 11Mbps Constantly receive 73 83 mA
Receive 11g 54Mbps Constantly receive 75 84 mA
Receive 11n MCS 7 Constantly receive 75 84 mA

Operating current

Working mode Working status, Ta = 25°C Average value Maximum value (Typical value) Unit
Quick network connection state (Bluetooth) The module is in the fast network connection state and the Wi-Fi indicator flashes fast 82 360 mA
Quick network connection state (AP) The module is in the hotspot network connection state and the Wi-Fi indicator flashes slowly 80 380 mA
Quick network connection state (EZ) The module is in the fast network connection state and the Wi-Fi indicator flashes fast 87 380 mA
Connected The module is in connected state and the Wi-Fi indicator light is always on 80 390 mA
Weakly connected The module and the hotspot are in the state of weak connection and the Wi-Fi indicator light is always on 205 390 mA
Disconnected The module is in disconnected state and the Wi-Fi indicator light is always off 75 367 mA

RF parameters

Basic RF features

Parameter Description
Working frequency 2.412 to 2.480 GHz
Wi-Fi standard IEEE 802.11 b/g/n (channels 1 to 14)
Data transmission rate 11b: 1, 2, 5.5, 11 (Mbps)
11g: 6, 9, 12, 18, 24, 36, 48, 54 (Mbps)
11n: HT20 MCS0-7
Antenna type External monopole sub-antenna

Wi-Fi transmission performance

Parameter Minimum value Typical value Maximum value Unit
Average RF output power, 802.11b CCK Mode 11M - 16 - dBm
Average RF output power, 802.11g OFDM Mode 54M - 15 - dBm
Average RF output power, 802.11n HT20 OFDM Mode MCS7 - 14 - dBm
Frequency error -20 - 20 ppm

Wi-Fi receiving performance

Parameter Minimum value Typical value Maximum value Unit
PER<8%, RX sensitivity, 802.11b DSSS Mode 11M - -88 - dBm
PER<10%, RX sensitivity, 802.11g OFDM Mode 54M - -75 - dBm
PER<10%, RX sensitivity, 802.11n HT20 OFDM Mode MCS7 - -72 - dBm
PER<10%, RX sensitivity, Bluetooth 1M - -93 - dBm

Bluetooth transmission performance

Parameter Minimum value Typical value Maximum value Unit
Working frequency 2402 - 2480 MHz
Air rate - 1 - Mbps
TX power -20 6 20 dBm
Frequency error -150 - 150 kHz

Bluetooth receiving performance

Parameter Minimum value Typical value Maximum value Unit
RX sensitivity - -93 - dBm
Maximum RF signal input -10 - - dBm
Inter-modulation - - -23 dBm
Co-channel suppression ratio - 10 - dB

Antenna

Antenna type

CBLC5 supports the external monopole sub-antenna.

Antenna interference reduction

To ensure optimal Wi-Fi performance, it is recommended that the antenna be at least 15 mm away from other metal parts.
To prevent an adverse impact on the antenna radiation performance, avoid copper or traces within the antenna area.

Packaging and production instructions

Mechanical dimensions

CBLC5 Module DatasheetCBLC5 Module Datasheet

CBLC5 Module Datasheet

PCB package — plug-in

CBLC5 modules use insertion welding. The following figure shows the plug-in dimensions:

CBLC5 Module Datasheet

Note: The default outline dimension tolerance is ±0.35 mm, and the critical dimension tolerance is ±0.1 mm. If you have specific requirements on dimensions, specify them clearly in the datasheet after communication.

Production instructions

  1. For the Tuya in-line module, wave soldering is most preferred and manual soldering is less preferred. After being unpacked, the module must be soldered within 24 hours. Otherwise, it must be put into the drying cupboard where the RH is not greater than 10%; or it needs to be packaged under vacuum again and record the exposure time (the total exposure time cannot exceed 168 hours).
  2. Wave soldering devices and materials:
    • Wave soldering equipment
    • Wave soldering fixture
    • Constant-temperature soldering iron
    • Tin bar, tin wire, and flux
    • Thermal profiler
  3. Baking devices:
    • Cabinet oven
    • Anti-electrostatic and heat-resistant trays
    • Anti-electrostatic and heat-resistant gloves
  4. The module needs to be baked in the following cases:
    • The packaging bag is damaged before unpacking.
    • There is no humidity indicator card (HIC) in the packaging bag.
    • After unpacking, circles of 10% and above on the HIC become pink.
    • The total exposure time has lasted for over 168 hours since unpacking.
    • More than 12 months have passed since the sealing of the bag.
  5. Baking settings:
    • Temperature: 40°C and ≤ 5% RH for reel package and 125°C and ≤5% RH for tray package (please use the heat-resistant tray rather than a plastic container).
    • Time: 168 hours for reel package and 12 hours for tray package.
    • Alarm temperature: 50°C for reel package and 135°C for tray package.
    • Production-ready temperature after natural cooling: < 36°C.
    • Re-baking situation: If a module remains unused for over 168 hours after being baked, it needs to be baked again.
    • If a batch of modules is not baked within 168 hours, do not use the wave soldering to solder them. Because these modules are Level-3 moisture-sensitive devices, they are very likely to get damp when exposed beyond the allowable time. In this case, if they are soldered at high temperatures, it may result in device failure or poor soldering.
  6. In the whole production process, take electrostatic discharge (ESD) protective measures.
  7. To guarantee the quality of products, you must pay attention to the following items: The amount of soldering flux, the height of the wave peak, whether the tin slag and copper content in the wave soldering tank exceed standards, whether the window and thickness of the wave soldering fixture are appropriate, and whether the wave soldering oven temperature curve is appropriate.

Recommended oven temperature curve and temperature

Set oven temperatures according to the following temperature curve of wave soldering. The peak temperature is 260°C±5°C.

CBLC5 Module Datasheet

Recommended soldering temperature:

Suggestions on oven temperature curve of wave soldering Suggestions on manual soldering temperature
Preheat temperature 80 to 130 °C Soldering temperature 360±20°C
Preheat time 75 to 100s Soldering time <3s/point
Peak contact time 3 to 5s NA NA
Temperature of tin cylinder 260±5°C NA NA
Ramp-up slope ≤2°C/s NA NA
Ramp-down slope ≤6°C/s NA NA

Storage conditions

Storage conditions for a delivered module:

  • The moisture-proof bag is placed in an environment where the temperature is below 40°C and the relative humidity is lower than 90%.

  • The shelf life of a dry-packaged product is 12 months from the date when the product is packaged and sealed.

  • There is a humidity indicator card (HIC) in the packaging bag.

    CBLC5 Module Datasheet

    CBLC5 Module Datasheet

MOQ and packaging information

Product model MOQ (pcs) Shipping packaging method The number of modules per reel The number of reels per carton
CBLC5 6800 Tape reel 1700 4

Appendix: Statement

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this device.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Note: This device has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this device does cause harmful interference to radio or television reception, which can be determined by turning the device off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the device and receiver.
  • Connect the device to an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Radiation Exposure Statement

This device complies with FCC radiation exposure limits set forth for an uncontrolled rolled environment. This device should be installed and operated with a minimum distance of 20cm between the radiator and your body.

Important Note

This radio module must not be installed to co-locate and operate simultaneously with other radios in the host system except in accordance with FCC multi-transmitter product procedures. Additional testing and equipment authorization may be required to operate simultaneously with other radio.

The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible to the end-user.

The host product manufacturer is responsible for compliance with any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.

The end-user manual shall include all required regulatory information/warning as shown in this manual, including: This product must be installed and operated with a minimum distance of 20 cm between the radiator and user body.

The RF module is considered as a limited modular transmitter according to FCC rules. Even though the RF module gets an FCC ID, the host product manufacturer can not use the FCC ID on the final product directly. In these circumstances, the host product manufacturer integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining the FCC authorization by a Class II permissive change application or a new application.

Declaration of Conformity European Notice

CBLC5 Module Datasheet

Hereby, Hangzhou Tuya Information Technology Co., Ltd declares that this module product is in compliance with essential requirements and other relevant provisions of Directive 2014/53/EU,2011/65/EU. A copy of the Declaration of Conformity can be found at https://www.tuya.com

CBLC5 Module Datasheet

This product must not be disposed of as normal household waste, in accordance with the EU directive for waste electrical and electronic equipment (WEEE- 2012/19/EU). Instead, it should be disposed of by returning it to the point of sale, or to a municipal recycling collection point.

The device could be used with a separation distance of 20cm from the human body.